![]() To do this, click the “Advanced Setup” button to continue. #NZXT AER RGB 2 ALTERNATIVE SOFTWARE#For 5V RGB devices however, we’ll need to tell the CAM software how many LEDs are in the device. For 12V RGB devices, you can go ahead and select “Save’ from here and the device should be ready to go. For this example, we’ve selected the “Other” option for a GPU backplate. With the “Configure RGB Product” window open, select how you would like your RGB device to be seen. In this case we’ll go with the 5V_ARGB1 header. Select the type of 3rd Party Devices you’d like to configure based on the port(s) you used by clicking the gear next to the port. To start adding your RGB device, open the “Lighting” tab on the CAM software and select “About the … Motherboard” option.Ĭlicking this will bring you to the device’s status menu which will show you the status of all RGB headers on the motherboard as well as their available LEDs. Do not panic though, as this is normal behavior since we have not yet set the device up in the CAM software. With your 3rd party RGB device connected to the motherboard, you may notice the device will light up bright white on startup but then immediately turn off when the CAM software starts. Setting up 3rd Party Devices in the NZXT CAM software #NZXT AER RGB 2 ALTERNATIVE SERIES#In addition to this, NZXT RGB devices will detect natively when connected to a CAM powered controller like that found on the N series motherboards. ![]() For more information as to which connector to use, refer to your device’s manual.įinally the third type supported by NZXT motherboards is NZXT RGB, which takes the groundwork of 5V ARGB and expands upon it for cleaner, more responsive effects across fans, LED strips, and other RGB products. Mixing these connections can result in damage to the RGB device or your motherboard. 12V is an older standard for RGB and may be found with older cases while 5V ARGB is a newer standard that is seeing wider spread adoption.īe careful when connecting these devices however, as it is easy to accidentally plug a 5V RGB device into 12V and vice-versa. For Analog RGB devices however, you are limited to a single color for the entire RGB strip. Put simply, with a Digital LED device such as an ARGB strip you can control each individual LED’s color and brightness to create animations and gradients within the strip itself. The two most common types of RGB products that you will find are 5V ARGB and 12V RGB, with the main difference between the two aside from their input voltage being that 5V ARGB is a Digital standard while 12V is an Analog standard. NZXT RGBīefore jumping into the CAM software, it is best to look at the differences between the three types of RGB that your NZXT motherboard supports. In this guide we’ll cover setting up your latest RGB component for your CAM software to be ready for your latest flex post. However unlike the F-series RGB fans or NZXT Underglow kit these devices need a helping hand to be seen by the NZXT CAM software. So, it depends on what you are looking to do with the RGB.Whether it be that sweet new RGB waterblock for your custom loop system or an accent strip to make your system’s lighting pop you may have a need to use either a 5V Addressable RGB (ARGB) device or 12V RGB device with your system. For instance, I have a profile where the two radiator fans vary their color based on liquid temperature and the two case fans' color changes based on GPU temperature (blue for idle, green for normal, yellow for getting warm, and red if its hotter than I'd like. ![]() I could have just used the Z63's single channel to control all four fans, but I wanted to be able to run different effects on them. In my recent build, I put two AER RGB 2 fans on my Z63's controller and two more as case fans on a NZXT Fan and RGB Controller. The "NZXT Fan and RGB Controller" has two channels and can control the lighting for up to 10 fans total (up to 5 on each channel, or some other combo of 40 LED with lighting strips or whatever). To control more than 5 fans, or more than one effect on some of those fans, you would need another controller. It will control up to 5 fans with a single effect. The Z73 has a single-channel controller built in. You can daisy-chain up to 5 of them (8x5=40) per channel. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |